Home | Contact | Pro Drywall Tips | Donate | Ask The Pro | Textures | Tools | Videos | Links  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

HOW TO DO A SLAPBRUSH TEXTURE    PAGE 2 OF 2

Step 5: Roll Out Each Row

Your next roller full of mud  will go the next row over (See Picture). Start on the right side and roll it to the left. The next row, start on the left and roll to your right. By switching every row it makes the mud even. This will make the texture more uniform.

     

  Step 6: Cross it the other way

Once you have your big section all rolled out. Roll over it again the opposite direction.

You are not adding any more mud, you're are just crossing over it to make everything nice and even.

   

  Step 7: Butter Up Your Brush, Start Slapping

Using the roller apply a generous bed of mud on the face of your slap brush. This is only done when you are first starting with a dry brush. You don't have to put mud on the brush for each new section. Now for the fun part, start slapping. I usually do a little in the middle just to break the brush in. Go along the outside edges first. Don't let the brush slide too far down the wall, you will have to wipe the walls clean so the less mud on the walls the better..

   

Step 8: Rotate The brush

Make sure to keep the brush spinning with every slap go left and right, up and down. Hit the ceiling pretty hard. If you hit it too soft mud will build up on your brush and before long,  it will get bery heavy. If you hit too hard you might start popping screws on the ceiling. If you don't rotate the brush you will get some noticeable patterns going. You don't want that..

Smack, Spin 1/2 turn, Smack, Spin 1/2 turn. The spin happens while the brush is in space. Don't spin it while it's touching the ceiling.

Step 9: Slap away any edges

Make sure not to leave any edges on the outside of your section. Any noticeable roller lines that are not slapped away might show through your finished ceiling.

That should be it for your 1st section. Don't over slap it but slap it enough to even it all out.

 

Step 10: Wipe Angles

I am pretty fast at this. I usually wipe my angles after the whole ceiling is textured.

You are a rookie and probably a little bit slower, I would suggest that you wipe your angles after each section.

This way the angles won't dry out.

Start by taking a six inch taping knife, dip it into the same bucket of mud you're texturing with. Get a little bit of mud in your drywall pan. Now apply a light bed of mud right up there in your angle close to the ceiling. Don't go into the ceiling.

      

 Pull your knife across the angle wiping off all the excess mud. This take a little practice. If you find yourself leaving little lines in the ceiling, get out your finger tool it do a little finger stomping.     

      

Wipe your corners form the inside out. Try your best, You can always do a little sanding after it dries.

      

One Section Done!

  

Step 11: Next Section

That's pretty much it. Keep working your way around the room doing manageable sized sections at a time. Don't leave any edges to dry out and you should be in great shape.

   

One Ceiling Done

Here you see a picture of the complete ceiling along with a picture of the same room after the whole room has been painted.

   

  Patches??

I get a lot of e-mails asking about how to blend patches when doing a slap brush..

The hardest thing about patches is that there will be like a sharp edge or line where the old meets the new.

If you can make that edge go away your patch will turn out much better. This is a trick my dad showed me.

Hang, tape and 1st coat the patch. After you 2nd coat the patch, right then while the mud is still wet, take a wadded up piece of plastic (like a plastic bag) and kind of tap on that outside edge (kind of like a pre-texture to the real texture) but only on that edge. This way after it dries, the edge is already blended in.

Questions that I receive?? (might help if your having problems)

Problem: Roller Won't Spin

Good Morning Mike, Over the weekend, I successfully textured my existing ceiling and new wall.  I went by your directions, and it turned out great.  I have some more texture work to do in the near future and wanted to ask you a few questions.  I was using a nap roller to put the texture on.  When I would dip it, shake it, and slide it, I would have trouble in initially rolling, it would smear for a little, and then begin rolling.  I would roll the thicker smeared area and thin it out.  It would work out ok.  The roller appeared to be full after I shook it and slid it.  Is the problem created by the mud being too thick?  I would appreciate your suggestions.

Thanks, Steve D. Hodges

It's either a real cheap roller or the mud is too thick, mix it a little thinner yet.  You might have made it what you thought was thin? It might be so thin You're worried you made it too thin, trust me, you didn't,

"When it's nice and thin, the roller will spin" ....Mike

 

Drywallschool.com grants you permission to view this Site and to print individual pages from this Site for your own personal, noncommercial use, provided that you agree to and accept without modification the notices, terms and conditions set forth in this agreement. You may not modify, copy (except as set forth in the preceding sentence), distribute, transmit, display, perform, reproduce, publish, license, create derivative works from, transfer or sell any information, material, software, products or services from this Site.

 Home | Contact | Pro Drywall Tips | Donate | Ask The Pro | Textures | Tools | Videos | Links

1999-2015  Drywallschool.Com , All Rights Reserved.